Defender Home Page
Phone: 800-628-8225 Fax: 800-654-1616 Int'l.: 860-701-3400 Email: Contact Us
Follow us on Facebook
Shipping Info
Defender Home Page
Your Cart
null View Cart View Shopping Cart
null Check My Order(s)
null Track My Package(s)
Conversion Chart
Shopping Areas
Boats & Motors
null Defender Seal null
promo A
promo B
promo C
promo D

Lenco Aftermarket Digital Auto Glide Kit with NMEA GPS Antenna-Single Actuator

  • Applications: All Engines without Existing NMEA 2000 Network
  • Boat must have Lenco Single Trim Tab System with Lenco Electric Actuator
  • Automatically Controls Trim Tabs for the Most Efficient Running Angle
  • Item #: 
    Model #: 


    Shipping Weight: 
    4.45 Lbs.
    List Price: 
    Reg. Price:
    Sale Price:
    Note:  This item ships from the manufacturer.
    It typically ships within 2 business days  (more...)
    Status:   null Ships Direct

    Quantity : 


    Click Here to See the Owner's Manual-A for this Product ( Installation and Setup Procedures)

    Click Here to See the Owner's Manual-B for this Product (Operational Instructions)


    • Boat must have a Lenco Single Trim Tab System with Lenco Electric Actuators
      • This is a MUST in all applications
    • A Real Automatic Boat Control / Trim Tab Control System that actually works
      • Completely & automatically!
    • The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again
    • The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed
      • This optimum running angle is determined during the set-up process after the installation of your Auto Glide system
    • Imagine that your boat’s running angle is measured 25 times per second and this data is used by the new Auto Glide control box to:
      • Automatically put your boat in the most efficient running angle
      • Reduce the amount of bow rise of your boat during hole shot mode
      • Eliminate bow porpoising (bow bounce)
      • Keep your boat level at all times
    • These actions will result in a smoother ride and the best possible fuel efficiency
    • The Auto Glide Control Box (brain) consists of gyroscopes, accelerometers, and new, very sophisticated, and patented software
    • The Auto Glide has (3) Automatic operational modes, (4) Automatic settings, and (2) Manual operational modes
      • Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the (4) Up/Down Buttons on the key pad
      • All of these functions are fully explained in our Owner’s Manual B / Operational Instructions
    • Notes:
      • The Auto Glide does not control the “trim” function of your Engine(s) or Motor(s)
      • Please remember to use the trim feature exactly as you would in the normal operation of your boat

    Components of the Auto Glide System:

    • The main components:
      • Auto Glide Key Pad
      • Auto Glide Control Box (Single Actuator and Double Actuator per Trim Tab Versions)
      • Control Box Main Harness (Same 2 versions)
      • Includes External GPS Antenna
      • Various cables
        • These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver
    • Second Station Kits and a vast array of other accessories and parts which may be required for your installation are also available (Purchased Separately)
    • Lenco offers Aftermarket Kits for easy installation on ALL boats, CANbus-equipped or not
    • OEM applications can be specially kitted to be boat or OEM specific


    • Aftermarket Systems:
      • The Lenco Glide System will work on ALL boats with ALL engines
      • GPS data is used to provide data to control box
      • Optional connection to NMEA 2000 Network is included
    • OEM System:
      • Connection to analog systems is available.
      • Connection to CANbus-based engines is available. See list below
      • Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver.
      • NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket
    • CANbus-based engines:
      • NMEA 2000 Engines
        • Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway
        • Evinrude
        • Honda
        • Suzuki
        • Volvo Penta (Non-EVC Engines) (With a Volvo NMEA 2000 Gateway - Volvo P/N 3889757)
      • J1939 Engines
        • Volvo Penta (EVC Engines)
        • Yanmar
        • Caterpillar
        • Cummins
        • Detroit Diesel
        • John Deere
        • Stey
      • Smart Craft Engines
        • Mercury - Verado
        • Mercury - Optimax with SmartCraft ECU
        • Mercruiser with SmartCraft ECU
        • Cummins/Mercruiser w/ SmartCraft ECU
    • Installation Notes:
      • The Auto Glide can be connected to your engine’s CANbus system, to your boat’s GPS system (direct to unit or network) or to a GPS Stand-Alone antenna/receiver
      • Different systems and applications present unique challenges
      • You may want to consider soliciting the help of an installer that possesses experience in CANbus systems, connecting products to GPS networks, etc., and/or NMEA 2000 Network experience
      • Lenco's Aftermarket Kits include a “Must Install” GPS antenna/receiver and can be installed by most marine mechanics and do-it-yourselfers
      • A Schematic must be printed from internet site (or print from PDF download) and must be followed exactly as shown.

    Lenco Aftermarket Digital Auto Glide Kit with NMEA GPS Antenna - Dual Actuator
    Item #: 305340
  • Applications: All Engines without Existing NMEA 2000 Network
  • Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators
  • Automatically Controls Trim Tabs for the Most Efficient Running Angle
  •  Include
    Reg. Price

    Sale Price

    Model #:
    Lenco Digital Auto Glide Kit without GPS Antenna or Network - Single Actuator
    Item #: 305813
  • Applications: All Engines with Existing NMEA 2000 Network (Except Volvo)
  • Boat must have Lenco Single Trim Tab System with Lenco Electric Actuator
  • Automatically Controls Trim Tabs for the Most Efficient Running Angle
  •  Include
    Reg. Price

    Sale Price

    Model #:

    Have A Suggestion?

    Help us make our site better for everyone! Let us know you've found something wrong or frustrating on this page and we will improve it. Please mark each that apply.

    Product has been improperly categorized
    Page loads too slowly
    Product information is incorrect
    Page has errors or bugs
    Site is frustrating or difficult to use
    Product image is missing or wrong
    Cannot find my size
    Spelling errors on page
    Not enough product information

    Comments or Examples:
    Examples: Missing information such as dimensions and model number, typos, inaccuracies, etc...

    Please include your e-mail address below if you would like us to respond to your comments or questions.             

    Join Our Email List And Receive our Monthly Promotions
    Defender Email Specials
    Click Here For Our Privacy Policy