Defender Home Page
Call or email to speak with our In-House Technical Staff/Advisors
Phone: 800-628-8225 Int'l.: 860-701-3400 Email: Contact Us
Follow us on Facebook
Shipping Info
Defender Home Page
Your Cart
null
null
null View Cart View Shopping Cart
null Check My Order(s)
null Track My Package(s)
Metric/Inch
Conversion Chart
Categories
Shopping Areas
Information
Boats & Motors
null Defender Seal null
promo A
promo B
promo C
promo D
 
 

Shaft Shark 500 Line and Weed Cutter

  • Keep your Prop Free from Rope, Weeds and Underwater Debris
  • Overall Diam.: 4.75", Split Design - No Prop Removal Required to Install
  • Shaft Diameter: 2.25"
  • Item #: 
    614770214SPL
    Brand: 
    Shaft Shark
    Model #: 

    SS500-2.250

    Packaged Weight: 
    1.60 Lbs.
    List Price: 
    $786.00
    Reg. Price:
    $628.99
    Sale Price:
    $597.54
    614770214SPL Shaft Shark Shaft Shark 500 Line and Weed Cutter SS500-2.250

    The Shaft Shark is a serrated edge disc, machined from high quality type 316 stainless steel. The internal diameter is machined to fit the shaft diameter of your boat - either metric or standard. Attached to your propeller shaft, it rotates with the shaft, cutting anything that might try to become entangled around your shaft and prop. Shark Shaft cuts through lines, nets and other underwater debris as soon as it catches.

    Features:

    • Keeps your propeller free from rope, weeds and underwater debris
    • Eliminates the need for towing due to fouled stern gear or propeller
    • Eliminates dangerous dives to clear your prop
    • Eliminates possible shaft and strut damage
    • Split design eliminates the need to remove propeller for installation
    • Does not require drilling of the shaft which can threaten shaft integrity

    Model Selection:

    The correct model for your boat will depend on your shaft diameter and your propeller hub diameter. For example, if the forward end hub diameter is 4.00 inches then you will need SS500 as this cutting area has a diameter of almost 5.00 inches. The SS400 is just less than 4.00 inches so there would be no "cutting area" extending past the hub diameter to cut the line.

    Installation:

    Installation is simple and quick. No drilling or tapping and no need to remove the propeller for installation. Can easily be installed underwater by a diver. The Shaft Shark requires just a small clearance fore and aft between the cutlass bearing and the propeller hub (see dimension "D" in diagram below). This dimension allows for sufficient clearance with the cutlass bearing for shaft movement when maneuvering and for water-flow through the cutlass bearing. Always install the Shaft Shark as close to the propeller as possible.

    Dimensions (See diagram below):

    Shaft Shark Model #
    SS300
    SS400
    SS500
    SS600
    B
    3.20"
    3.98"
    4.75"
    5.875"
    C
    2.25"
    3.00"
    3.625"
    4.45"
    D
    .72"
    .72"
    .82"
    1.25"

    The Shaft Shark is a serrated edge disc, machined from high quality type 316 stainless steel. The internal diameter is machined to fit the shaft diameter of your boat - either metric or standard. Attached to your propeller shaft, it rotates with the shaft, cutting anything that might try to become entangled around your shaft and prop. Shark Shaft cuts through lines, nets and other underwater debris as soon as it catches.

    Features:

    • Keeps your propeller free from rope, weeds and underwater debris
    • Eliminates the need for towing due to fouled stern gear or propeller
    • Eliminates dangerous dives to clear your prop
    • Eliminates possible shaft and strut damage
    • Split design eliminates the need to remove propeller for installation
    • Does not require drilling of the shaft which can threaten shaft integrity

    Model Selection:

    The correct model for your boat will depend on your shaft diameter and your propeller hub diameter. For example, if the forward end hub diameter is 4.00 inches then you will need SS500 as this cutting area has a diameter of almost 5.00 inches. The SS400 is just less than 4.00 inches so there would be no "cutting area" extending past the hub diameter to cut the line.

    Installation:

    Installation is simple and quick. No drilling or tapping and no need to remove the propeller for installation. Can easily be installed underwater by a diver. The Shaft Shark requires just a small clearance fore and aft between the cutlass bearing and the propeller hub (see dimension "D" in diagram below). This dimension allows for sufficient clearance with the cutlass bearing for shaft movement when maneuvering and for water-flow through the cutlass bearing. Always install the Shaft Shark as close to the propeller as possible.

    Dimensions (See diagram below):

    Shaft Shark Model #
    SS300
    SS400
    SS500
    SS600
    B
    3.20"
    3.98"
    4.75"
    5.875"
    C
    2.25"
    3.00"
    3.625"
    4.45"
    D
    .72"
    .72"
    .82"
    1.25"
    Shaft Shark 500 Line and Weed Cutter
    597.54
    Status:    null In Stock

     

    shipping delay

     

    The Shaft Shark is a serrated edge disc, machined from high quality type 316 stainless steel. The internal diameter is machined to fit the shaft diameter of your boat - either metric or standard. Attached to your propeller shaft, it rotates with the shaft, cutting anything that might try to become entangled around your shaft and prop. Shark Shaft cuts through lines, nets and other underwater debris as soon as it catches.

    Features:

    • Keeps your propeller free from rope, weeds and underwater debris
    • Eliminates the need for towing due to fouled stern gear or propeller
    • Eliminates dangerous dives to clear your prop
    • Eliminates possible shaft and strut damage
    • Split design eliminates the need to remove propeller for installation
    • Does not require drilling of the shaft which can threaten shaft integrity

    Model Selection:

    The correct model for your boat will depend on your shaft diameter and your propeller hub diameter. For example, if the forward end hub diameter is 4.00 inches then you will need SS500 as this cutting area has a diameter of almost 5.00 inches. The SS400 is just less than 4.00 inches so there would be no "cutting area" extending past the hub diameter to cut the line.

    Installation:

    Installation is simple and quick. No drilling or tapping and no need to remove the propeller for installation. Can easily be installed underwater by a diver. The Shaft Shark requires just a small clearance fore and aft between the cutlass bearing and the propeller hub (see dimension "D" in diagram below). This dimension allows for sufficient clearance with the cutlass bearing for shaft movement when maneuvering and for water-flow through the cutlass bearing. Always install the Shaft Shark as close to the propeller as possible.

    Dimensions (See diagram below):

    Shaft Shark Model #
    SS300
    SS400
    SS500
    SS600
    B
    3.20"
    3.98"
    4.75"
    5.875"
    C
    2.25"
    3.00"
    3.625"
    4.45"
    D
    .72"
    .72"
    .82"
    1.25"

    The Shaft Shark is a serrated edge disc, machined from high quality type 316 stainless steel. The internal diameter is machined to fit the shaft diameter of your boat - either metric or standard. Attached to your propeller shaft, it rotates with the shaft, cutting anything that might try to become entangled around your shaft and prop. Shark Shaft cuts through lines, nets and other underwater debris as soon as it catches.

    Features:

    • Keeps your propeller free from rope, weeds and underwater debris
    • Eliminates the need for towing due to fouled stern gear or propeller
    • Eliminates dangerous dives to clear your prop
    • Eliminates possible shaft and strut damage
    • Split design eliminates the need to remove propeller for installation
    • Does not require drilling of the shaft which can threaten shaft integrity

    Model Selection:

    The correct model for your boat will depend on your shaft diameter and your propeller hub diameter. For example, if the forward end hub diameter is 4.00 inches then you will need SS500 as this cutting area has a diameter of almost 5.00 inches. The SS400 is just less than 4.00 inches so there would be no "cutting area" extending past the hub diameter to cut the line.

    Installation:

    Installation is simple and quick. No drilling or tapping and no need to remove the propeller for installation. Can easily be installed underwater by a diver. The Shaft Shark requires just a small clearance fore and aft between the cutlass bearing and the propeller hub (see dimension "D" in diagram below). This dimension allows for sufficient clearance with the cutlass bearing for shaft movement when maneuvering and for water-flow through the cutlass bearing. Always install the Shaft Shark as close to the propeller as possible.

    Dimensions (See diagram below):

    Shaft Shark Model #
    SS300
    SS400
    SS500
    SS600
    B
    3.20"
    3.98"
    4.75"
    5.875"
    C
    2.25"
    3.00"
    3.625"
    4.45"
    D
    .72"
    .72"
    .82"
    1.25"

    additional image

     
     

     
     

    Have A Suggestion?


    This form is intended to improve the current product page. For Customer Service, please click here

    Help us make our site better for everyone! Let us know you've found something wrong or frustrating on this page and we will improve it. Please mark each that apply.










    Comments or Examples:
    Examples: Missing information such as dimensions and model number, typos, inaccuracies, etc...

                





           
    Defender Email Specials
    Click Here For Our Privacy Policy
     
    null