Item #878385

Racor T-Handle Vacuum Indicator Gauge - RK32348

00 Review
$73.99
Want an email once available?
Buy with

Image of : Racor T-Handle Vacuum Indicator Gauge - RK32348 Racor T-Handle Vacuum Indicator Gauge - RK32348 Item # 878385

Description

Features:

  • Designed for use on all Racor 500 / 900 / 1000 Turbine Series Diesel Fuel Filter / Water Separator assemblies
  • This gauge measures the increase in vacuum due to contamination of the Filter
    • T-Handle Vacuum Restriction Indicator monitors the diesel filter's condition as the filter becomes clogged with contaminants
    • The T-Handle gauge accurately measures filter contamination with any size micron filter
    • As the filter gets dirty, restriction increases and less fuel is delivered to the engine, causing the engine to lose power and eventually stall
  • Installs in one easy spin:
    • Simply remove existing T-handle and replace with the RK32348 T-Handle Vacuum Indicator (Not a Kit / Fully assembled / Complete with O-ring)
  • The T-handle design allows for filter cover removal without tools
  • Maximizes fuel filter life and lengthens fuel filter change out intervals
  • Easy to read:
    • Locks in position at highest measured filter contamination level
    • When the Yellow internal indicator approaches the Red Zone, Change the Filter. (Red Zone indicates 10" Hg vacuum) Green Zone " Good To Go"
    • 360° Viewable
    • The gauge can be read anytime, even days after the engine has been off
  • Internal Check Valve:
    • The T-Handle has a check valve to allow usage with priming pumps and prevent leaks if the gauge is damaged
  • Easy and Safe Reset Button:
    • Located on top of gauge, and never opens gauge to the outside atmosphere
  • Works as a Diagnostic tool for other fuel problems:
    • Helps to Diagnose: ( After filter change)
      • Collapsing fuel lines
      • Bad / Closed fuel valves
      • Clogged fuel pick-ups
      • Heavily Contaminated fuel tanks
  • Takes the guesswork out of diesel fuel filter maintenance:
    • Maximize filter life, Stop Guessing when to change filters
    • Know immediately when bad fuel is pumped onboard
  • All components are 100% Diesel Fuel Compatible
    • Use with diesel, bio-diesel, and kerosene
  • Lowers operational costs / down time
  • Helps to keep unnecessarily changed filters from being discarded
  • Made in the U.S.A.

Specifications:

  • Accuracy: ± 10%
  • Calibration: 10 inHg (34 kPa) at Red zone
  • Material: Brass and Chemical Resistant Nylon
  • 2.5 " (6.4 cm) higher than original T-Handle / Over all height 4.8" (12.2 cm)
  • Thread Size: 1/4" NPT
  • Operating Temperature -40° to +250°F (-40° to +121°C)

Note: Not for use in Gasoline Applications

Installation Note:

  • Hand Tighten ONLY - The T-handle should ONLY be hand tight
  • That DOES NOT mean as tight as you can get it by hand and it certainly does not mean use two hands
  • The 0-ring seals the T-handle to the lid and only needs to be snug
  • Over tightening the T-handle can damage both the 0-ring on the t-handle and the 0-ring inside the filter cover
  • 0-Rrings seal surprisingly easily, at very low torque and seldom loosen up

Part Numbers for Racor T-Handle Vacuum Indicator Gauge - RK32348

Reviews

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 28.13ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Questions

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 24.29ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;